Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
Were you trying to locate answers around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't exactly brain surgery, however it does require solid plumbing, woodworking, and often, tiling abilities. Changing an old tub with a brand-new one is also a moderately hard project. If the old tub is conveniently obtainable, the job can relocate easily; if you have to open up a wall to eliminate the old bathtub and position the brand-new tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need a helper to move out the old bathtub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the task as well as fit attempting it. Instead of working with a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might require a professional plumber to make tube links.
This write-up will assist you set up a brand-new bathtub in your shower room if you have actually already acquired a brand-new bathtub and also don't require to alter the setup of your previous water pipes.
Your devices as well as material checklist should consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing taps can be rather troublesome due to the limited access that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before going on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washing machines are in area in between the faucet and also the sink. Protect the faucet in place with the manufacturer offered backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The former kind must be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are practical in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub till the spirit level reads degree.
To mount faucets, fit all-time low of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water supply as well as check all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and likewise examine the overflow outlet and also the normal outlet for leakages.
Finally, take care of the bathroom paneling as explained in the producer's user's manual. Tiling as well as securing around the tub should wait up until the bathtub has actually been used a minimum of once as this will resolve it into its last placement.
Getting ready for the Installation
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, causing issues with moisture and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and fittings. They are offered in tubes and cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that blog posting on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the search engines. Enjoyed our blog entry? Please share it. Let somebody else find it. I recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Get relief now! Report this page